Outback FM80 Flexmax 80 MPPT 80 AMP Solar Charge Controller Outback Power

Sold on eBay


Description

Outback Flexmax 80 FM80 MPPT 80 AMP Solar Charge Controller
Outback Power Systems
FLEXmax 80
MPPT Charge Controller

The FLEXmax 80 is the up to date innovation in Maximum Power Point Tracking (MPPT) charge controllers from OutBack Power Systems. The FLEXmax 80’s innovative MPPT Set of rules is both continuous and active, increasing your renewable energy yield up to 30%. Thanks to enhanced cooling, the FLEXmax 80 can operate at its full 80 amp maximum current rating in ambient temperatures as high as 104°F (40°C).

Included in the FLEXmax 80 are the entire features first developed by OutBack Power in the revolutionary MX60, such as make stronger for quite a lot of nominal battery voltages and the ability to step-down a high voltage solar array to recharge a low voltage battery. A built-in backlit display shows status information at the touch of a button. Enhanced network communications allow the FLEXmax 80 to be remotely programmed by way of the optional MATE system display and controller.

The new FLEXmax 80 is the only choice whilst you demand a high performance, efficient and customizable charge controller for your advanced power system.

Features:

  • Increases PV Array Output by up to 30%
  • Advanced Continuous Maximum Power Point Tracking Algorithm
  • Full Output Capacity in Ambient Temperatures up to 104°F (40°C)
  • Battery Voltages from 12 VDC to 60 VDC
  • Automatic Battery Voltage Detection at Start Up
  • Fully OutBack Network Integrated and Programmable
  • Programmable Auxiliary Regulate Output
  • Negative or Positive Ground System Capable
  • Built-in 128 days of Data Logging

 

FLEXmax™ 80 Specifications*
Nominal Battery Voltages
12, 24, 36, 48, or 60 VDC (Single model – selectable by way of field programming at start-up)
Maximum Output Current
80 amps @ 104° F (40°C) with adjustable current limit
Maximum Solar Array STC Nameplate
12 VDC systems 1250 Watts / 24 VDC systems 2500 Watts / 48 VDC systems 5000 Watts / 60 VDC Systems 7500 Watts
NEC Advisable Solar Array STC Nameplate
12 VDC systems 1000 Watts / 24 VDC systems 2000 Watts / 48 VDC systems 4000 Watts / 60 VDC Systems 5000 Watts
PV Open Circuit Voltage (VOC)
150 VDC absolute maximum coldest conditions / 145 VDC start-up and operating maximum
Standby Power Consumption
Less than 1 Watt typical
Power Conversion Efficiency
97.5% @ 80 Amps in a 48 VDC System – Typical
Charging Regulation
Five Stages: Bulk, Absorption, Waft, Silent and Equalization
Voltage Regulation Set points
10 to 80 VDC user adjustable with password protection
Equalization Charging Programmable Voltage Setpoint and Duration – Automatic Termination when completed
Battery Temperature Compensation
Automatic with optional RTS installed / 5.0 mV per °C per 2V battery cell
Voltage Step-Down Capability
Can charge a lower voltage battery from a higher voltage PV array – Max 150 VDC input
Programmable Auxilary Regulate Output
12 VDC output signal which will also be programmed for different Regulate applications (Maximum of 0.2 amps DC)
Status Display
3.1″ (8 cm) backlit LCD screen – 4 lines with 80 alphanumeric characters total
Remote Display and Controller

Optional Mate or Mate2 with RS232 Serial Communications Port

Network Cabeling
Proprietary network system the use of RJ 45 Modular Connectors with CAT 5e Cable (8 wires)
Data Logging
Last 128 days of Operation – Amp Hours, Watt Hours, Time in Waft , Peak Watts, Amps, Solar Array Voltage, Max Battery Voltage Min Battery Voltage and Absorb for on a daily basis together with total Accumulated Amp Hours, and kW Hours of production
Hydro Turbine Applications
Consult factory for approved Turbines
Positive Ground Applications
Requires two Pole Breakers for switching both positive and Negative Conductors on both Solar Array and Battery Connections (HUB-4 and HUB-10 can’t be used to be used in positive ground applications)
Operating Temperature Range Minimum -40° to maximum 60° C (Power capacity of the controller is mechanically derated when operated above 40° C)
Environmental Rating Indoor Type 1
Physical Specifications
Conduit Knockouts One 1″ (35mm)at the back; One1″ (35mm) at the left side; Two 1″ (35mm) at the bottom
Warranty Standard 5 year
Weight – Unit, 12.20 lbs (5.56 kg)
  – Shipping, 15.75 lbs (7.10 kg)
Dimensions – Unit 16.25″ x 5.75″ x 4″ (41.3 x 14 x 10 cm) – (H x W x D)
  – Shipping 21″ x 10.5″ x 9.75″ (53 x 27 x 25 cm)
Options Remote Temperature Sensor (RTS), HUB 4, HUB 10, MATE, MATE 2
Menu Languages English & Spanish

Use appropriate wire size in response to NEC.
* Specifications subject to change without notice.

 

Hurricane Wind Power
Build News Magazine
Best Off Grid
2016
Product Supplier
Renewable Energy
UP TO 50% DISCOUNTS
TOP BRANDS

Payment
Shipping
Returns

 

We accept payment by any of the following methods:

 

PayPal

 

Please pay as soon as conceivable after winning an auction, as with a view to allow us to post your item to you sooner!

We offer Fast shipping on all orders!

Your order might be dispatched within 1-3 working day of receiving payment (Monday-Friday) and you will have to expect to receive it one or two days after dispatch (for orders sent RM 1st Class).

In the very unlikely event that your item is lost or damaged throughout post, then WE are responsible and will issue either a full refund or replacement.

 

If you don’t seem to be 100% satisfied with your purchase, you’ll return the product and get a full refund or exchange the product for every other one, be it similar or not.

 

You can return a product for up to 14 days from the date you purchased it.

Any product you return will have to be in the same condition you received it and in the original packaging. Please keep the receipt.

Thank you for visiting our Ebay store!
Outback Power Systems FLEXmax 80 MPPT Charge Controller The FLEXmax 80 is the up to date innovation in Maximum Power Point Tracking (MPPT) charge controllers from OutBack Power Systems. The FLEXmax 80’s innovative MPPT Set of rules is both continuous and active, increasing your renewable energy yield up to 30%. Thanks to enhanced cooling, the FLEXmax 80 can operate at its full 80 amp maximum current rating in ambient temperatures as high as 104°F (40°C). Included in the FLEXmax 80 are the entire features first developed by OutBack Power in the revolutionary MX60, such as make stronger for quite a lot of nominal battery voltages and the ability to step-down a high voltage solar array to recharge a low voltage battery. A built-in backlit display shows status information at the touch of a button. Enhanced network communications allow the FLEXmax 80 to be remotely programmed by way of the optional MATE system display and controller. The new FLEXmax 80 is the only choice whilst you demand a high performance, efficient and customizable charge controller for your advanced power system. Features: —Increases PV Array Output by up to 30% — Advanced Continuous Maximum Power Point Tracking Set of rules — Full Output Capacity in Ambient Temperatures up to 104°F (40°C) — Battery Voltages from 12 VDC to 60 VDC — Automatic Battery Voltage Detection at Start Up — Fully OutBack Network Integrated and Programmable — Programmable Auxiliary Regulate Output — Negative or Positive Ground System Capable — Built-in 128 days of Data Logging FLEXmax™ 80 Specifications* Nominal Battery Voltages 12, 24, 36, 48, or 60 VDC (Single model – selectable by way of field programming at start-up) Maximum Output Current 80 amps @ 104° F (40°C) with adjustable current limit Maximum Solar Array STC Nameplate 12 VDC systems 1250 Watts / 24 VDC systems 2500 Watts / 48 VDC systems 5000 Watts / 60 VDC Systems 7500 Watts NEC Advisable Solar Array STC Nameplate 12 VDC systems 1000 Watts / 24 VDC systems 2000 Watts / 48 VDC systems 4000 Watts / 60 VDC Systems 5000 Watts PV Open Circuit Voltage (VOC) 150 VDC absolute maximum coldest conditions / 145 VDC start-up and operating maximum Standby Power Consumption Not up to 1 Watt typical Power Conversion Efficiency 97.5% @ 80 Amps in a 48 VDC System – Typical Charging Regulation Five Stages: Bulk, Absorption, Waft, Silent and Equalization Voltage Regulation Set points 10 to 80 VDC user adjustable with password protection Equalization Charging Programmable Voltage Setpoint and Duration – Automatic Termination when completed Battery Temperature Compensation Automatic with optional RTS installed / 5.0 mV per °C per 2V battery cell Voltage Step-Down Capability Can charge a lower voltage battery from a higher voltage PV array – Max 150 VDC input Programmable Auxilary Regulate Output 12 VDC output signal which will also be programmed for different Regulate applications (Maximum of 0.2 amps DC) Status Display 3.1″ (8 cm) backlit LCD screen – 4 lines with 80 alphanumeric characters total Remote Display and Controller Optional Mate or Mate2 with RS232 Serial Communications Port Network Cabeling Proprietary network system the use of RJ 45 Modular Connectors with CAT 5e Cable (8 wires) Data Logging Last 128 days of Operation – Amp Hours, Watt Hours, Time in Waft , Peak Watts, Amps, Solar Array Voltage, Max Battery Voltage Min Battery Voltage and Absorb for on a daily basis together with total Accumulated Amp Hours, and kW Hours of production Hydro Turbine Applications Consult factory for approved Turbines Positive Ground Applications Requires two Pole Breakers for switching both positive and Negative Conductors on both Solar Array and Battery Connections (HUB-4 and HUB-10 can’t be used to be used in positive ground applications) Operating Temperature Range Minimum -40° to maximum 60° C (Power capacity of the controller is mechanically derated when operated above 40° C) Environmental Rating Indoor Type 1 Physical Specifications Conduit Knockouts One 1″ (35mm)at the back; One1″ (35mm) at the left side; Two 1″ (35mm) at the bottom Warranty Standard 5 year Weight – Unit, 12.20 lbs (5.56 kg) – Shipping, 15.75 lbs (7.10 kg) Dimensions – Unit 16.25″ x 5.75″ x 4″ (41.3 x 14 x 10 cm) – (H x W x D) – Shipping 21″ x 10.5″ x 9.75″ (53 x 27 x 25 cm) Options Remote Temperature Sensor (RTS), HUB 4, HUB 10, MATE, MATE 2 Menu Languages English & Spanish Use appropriate wire size in response to NEC. * Specifications subject to change without notice. [FREE! Sellers: Add a FREE map to your listings. FREE!] (https://newage.mystoremaps.com//echo/tagLine?sid=cea073c8-fc6f-494f-9ca5-610e8850a127&tid=1) Froo www.froo.com | Froo Cross Sell, Free Cross Sell, Cross promote, eBay Marketing, eBay listing Apps, eBay Apps, eBay Application
Outback Flexmax 80 FM80 MPPT 80 AMP Solar Charge Controller
Outback Power Systems
FLEXmax 80
MPPT Charge Controller

The FLEXmax 80 is the up to date innovation in Maximum Power Point Tracking (MPPT) charge controllers from OutBack Power Systems. The FLEXmax 80’s innovative MPPT Set of rules is both continuous and active, increasing your renewable energy yield up to 30%. Thanks to enhanced cooling, the FLEXmax 80 can operate at its full 80 amp maximum current rating in ambient temperatures as high as 104°F (40°C).

Included in the FLEXmax 80 are the entire features first developed by OutBack Power in the revolutionary MX60, such as make stronger for quite a lot of nominal battery voltages and the ability to step-down a high voltage solar array to recharge a low voltage battery. A built-in backlit display shows status information at the touch of a button. Enhanced network communications allow the FLEXmax 80 to be remotely programmed by way of the optional MATE system display and controller.

The new FLEXmax 80 is the only choice whilst you demand a high performance, efficient and customizable charge controller for your advanced power system.

Features:

  • Increases PV Array Output by up to 30%
  • Advanced Continuous Maximum Power Point Tracking Algorithm
  • Full Output Capacity in Ambient Temperatures up to 104°F (40°C)
  • Battery Voltages from 12 VDC to 60 VDC
  • Automatic Battery Voltage Detection at Start Up
  • Fully OutBack Network Integrated and Programmable
  • Programmable Auxiliary Regulate Output
  • Negative or Positive Ground System Capable
  • Built-in 128 days of Data Logging

 

FLEXmax™ 80 Specifications*
Nominal Battery Voltages
12, 24, 36, 48, or 60 VDC (Single model – selectable by way of field programming at start-up)
Maximum Output Current
80 amps @ 104° F (40°C) with adjustable current limit
Maximum Solar Array STC Nameplate
12 VDC systems 1250 Watts / 24 VDC systems 2500 Watts / 48 VDC systems 5000 Watts / 60 VDC Systems 7500 Watts
NEC Advisable Solar Array STC Nameplate
12 VDC systems 1000 Watts / 24 VDC systems 2000 Watts / 48 VDC systems 4000 Watts / 60 VDC Systems 5000 Watts
PV Open Circuit Voltage (VOC)
150 VDC absolute maximum coldest conditions / 145 VDC start-up and operating maximum
Standby Power Consumption
Less than 1 Watt typical
Power Conversion Efficiency
97.5% @ 80 Amps in a 48 VDC System – Typical
Charging Regulation
Five Stages: Bulk, Absorption, Waft, Silent and Equalization
Voltage Regulation Set points
10 to 80 VDC user adjustable with password protection
Equalization Charging Programmable Voltage Setpoint and Duration – Automatic Termination when completed
Battery Temperature Compensation
Automatic with optional RTS installed / 5.0 mV per °C per 2V battery cell
Voltage Step-Down Capability
Can charge a lower voltage battery from a higher voltage PV array – Max 150 VDC input
Programmable Auxilary Regulate Output
12 VDC output signal which will also be programmed for different Regulate applications (Maximum of 0.2 amps DC)
Status Display
3.1″ (8 cm) backlit LCD screen – 4 lines with 80 alphanumeric characters total
Remote Display and Controller

Optional Mate or Mate2 with RS232 Serial Communications Port

Network Cabeling
Proprietary network system the use of RJ 45 Modular Connectors with CAT 5e Cable (8 wires)
Data Logging
Last 128 days of Operation – Amp Hours, Watt Hours, Time in Waft , Peak Watts, Amps, Solar Array Voltage, Max Battery Voltage Min Battery Voltage and Absorb for on a daily basis together with total Accumulated Amp Hours, and kW Hours of production
Hydro Turbine Applications
Consult factory for approved Turbines
Positive Ground Applications
Requires two Pole Breakers for switching both positive and Negative Conductors on both Solar Array and Battery Connections (HUB-4 and HUB-10 can’t be used to be used in positive ground applications)
Operating Temperature Range Minimum -40° to maximum 60° C (Power capacity of the controller is mechanically derated when operated above 40° C)
Environmental Rating Indoor Type 1
Physical Specifications
Conduit Knockouts One 1″ (35mm)at the back; One1″ (35mm) at the left side; Two 1″ (35mm) at the bottom
Warranty Standard 5 year
Weight – Unit, 12.20 lbs (5.56 kg)
  – Shipping, 15.75 lbs (7.10 kg)
Dimensions – Unit 16.25″ x 5.75″ x 4″ (41.3 x 14 x 10 cm) – (H x W x D)
  – Shipping 21″ x 10.5″ x 9.75″ (53 x 27 x 25 cm)
Options Remote Temperature Sensor (RTS), HUB 4, HUB 10, MATE, MATE 2
Menu Languages English & Spanish

Use appropriate wire size in response to NEC.
* Specifications subject to change without notice.

 

Froo www.froo.com | Froo Cross Sell, Free Cross Sell, Cross promote, eBay Marketing, eBay listing Apps, eBay Apps, eBay Application
Hurricane Wind Power
Build News Magazine
Best Off Grid
2016
Renewable Energy
Product Supplier
UP TO 50% DISCOUNTS
TOP BRANDS

 

We accept payment by any of the following methods:

 

PayPal

 

Please pay as soon as conceivable after winning an auction, as with a view to allow us to post your item to you sooner!

We offer Fast shipping on all orders!

Your order might be dispatched within 1-3 working day of receiving payment (Monday-Friday) and you will have to expect to receive it one or two days after dispatch (for orders sent RM 1st Class).

In the very unlikely event that your item is lost or damaged throughout post, then WE are responsible and will issue either a full refund or replacement.

 

If you don’t seem to be 100% satisfied with your purchase, you’ll return the product and get a full refund or exchange the product for every other one, be it similar or not.

 

You can return a product for up to 14 days from the date you purchased it.

Any product you return will have to be in the same condition you received it and in the original packaging. Please keep the receipt.

Thank you for visiting our Ebay store!

Additional information

brand

model

mpn

upc

Reviews

There are no reviews yet.

Be the first to review “Outback FM80 Flexmax 80 MPPT 80 AMP Solar Charge Controller Outback Power”